Verona VEFSGG365NBU Installation Manual

IMPORTANT - PLEASE READ AND FOLLOW✓ Before beginning, please read these instructions completely and carefully.✓ Do not remove permanently affixed la

10Fig. 1.4FITTING THE ADJUSTABLE FEETThe adjustable feet must be fitted to the base of the cooker before use.Rest the rear of the cooker on a piece o

11ABABAABBFig. 1.8Fig. 1.9ASSEMBLING THE BACKGUARD OR THE ISLAND TRIMIt is mandatory to install the backguard or the island trim• Assemble the backg

12ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS1. The anti-tip bracket has to be attached as shown on figure below, it has to be fixed on the re

13Gas supply lineShutoff valve“open” positionTo rangeFig. 2.1All gas connections must be made according to national and local codes. This gas supply (

14PRESSURE REGULATOR INSTALLATIONLOCKArrowSTEP 2Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gask

15AASTEP 3Insert the extension pipe + pressure regulator group in the “A” bracket.STEP 4Assemble the extension pipe + pressure regulator group to the

16BBSTEP 5Fix the “B” bracket on the back of the range by the 2 (two) screws supplied with the kit for gas connection.The regulator cover must be ordi

17ConnectorPressureregulator1/2” G cylindrical(ISO 228-1) female1/2” NPT(conical)male1/2” NPTfemale1/2” NPTfemale1/2” G cylindrical(ISO 228-1) maleExt

18Fig. 2.4TEST POINT ADAPTERThe Test Point adapter is available from the After-Sales Service.c) Any conversion required must be performed by your dea

1912NATURAL GASREGULATIONLP/PROPANEREGULATIONAcomponentFig. 2.5REGULATORCOVERPressure regulatorCONVERSION TO LP/PROPANE GASEvery range is provided wit

2✓ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.✓ WHAT TO DO IF YOU SMELL GAS:• D

20OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS✓ Remove the gratings and the burner covers;✓ Using a wrench substitute the nozzle inject

21SETTING THE BURNER MINIMUMWhen switching from one type of gas to another, the minimum flow rate must also be correct: the flame should not go out e

22OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTORS OF THE OVEN AND BROIL BURNERSa) Oven Burner – Lift and remove the lower panel inside

23ADJUSTMENT OF THE OVEN BURNER MINIMUMThis needs to be done only for the oven burner (the broil is a fixed capacity) by acting on the thermostat in t

24If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.Check

25WIRING DIAGRAM

26

27

Cod. 1104634 - ß1The manufacturer cannot be held re spon sible for possible inaccuracies due to printing or transcription errors in the present bookle

3DATA PLATECONVERSION LABELThis appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any

4WARNING!THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.Improper installation, adjustment, alteration, services, or maintenance can cause

5GENERAL INFORMATION1. Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-Lat

6installationPROXIMITY TO SIDE CABINETS1. This range may be installed directly adjacent to existing 36” (914 mm) high base cabinets. Range dimension

7CDBAGAS AND ELECTRIC CONNECTIONDotted line showing the positionof the range when installed* : Depending on feet regulationArea for GAS connectionArea

8(457 mm)18" min.30" min.(762 mm)(914 mm)36"0"(0 mm)0"(0 mm)20" min. (500 mm)11" 13/16 min. (300 mm)13" max. (

9Fig. 1.3cFig. 1.3dPROXIMITY TO SIDE CABINETSRANGE WITH ISLAND TRIM(457 mm)18" min.30" min.(762 mm)(914 mm)36"0"0"(0 mm)(0 m